Lyman Electronic Digital Trigger Pull Gauge

Lyman-Trigger-Gauge-02

Every wanted to know for sure what the pull weight of your trigger is? Made any modifications to your trigger, maybe the “25¢ Glock Trigger Job”?

With the Lyman trigger gauge, you can get a decent measurement of you triggers pull weight. So, if you are doing some gunsmithing, or are just curious, you can find out what your trigger pull is set to. This is especially good to know if you are doing any custom trigger work, like polishing or doing upgrades.
Read more

Glock Sight Comparison: Ameriglo vs Meprolight vs TruGlo TFO

Ameriglo-GL-115Meprolight-ML-10224ObTruGlo-TFO

I’m in the process of upgrading the sights on a few of my pistols so I figured I should get a variety of sights and do a quick once over on them all… In this round I have access to a set of Ameriglo (GL-115) sights, a set of Meprolight (ML-10224) sights and a set of TruGlo TFO (TG131GTIY) fiber optic sights; all are for standard Glock pistols (9mm, .40, etc) and are Tritium powered night sights.

It is worth noting, the Ameriglo sights are marked as Trijicon sights; from what I’ve read the metal portions of the sights are made by Ameriglo, but the Tritium inserts are designed and made by Trijicon.

Tritium (T, 3H)
Tritium is a radioactive isotope of Hydrogen that emits electrons that can cause phosphors to glow and be used as self-powered lighting devices called betalights. This is used in many things, like watches and night sights. Tritium is very expensive costing around $30,000 USD per gram.
more information >>

Lets see how they stack up…
Read more

Maryland Gun Works (MGW) Sight Pro Tool

MGW-Sight-Pro

I don’t know how it is in your area, but here in California, most gun shops either don’t install sights, charge an arm and a leg for the installation, or wont install them unless you buy them from them at inflated prices.

This led me to begin searching for a more economical way to install sights on a bunch of my guns, some friends guns, and for being able to do changes of sights for reviews and testing. In my search I found that there are more than a few options, everything from DIY style contraptions to specific branded installers for specific sight and gun models.

I wanted something that would last, work with multiple firearms, and not damage and slides, sights, or anything else for that matter. The only “real” option that I found was the MGW Sight Pro tool. I say real, because for my use, I wanted something that was good but not $600 and would work with a bunch of different models (instead of having 10 different tools). The Sight Pro can be picked up from places like Midway USA or Brownells for around $329.99.
  Read more

Malfunctioning AR-15 – The Story of a Seemingly Under-Gassed Rifle

I recently had the opportunity to help a friend with an AR-15 that he had pieced together, and then had a gunsmith “finish off”. The gunsmith put the upper assembly together and finished off the lower assembly.

After taking it to the range, the thing wouldn’t cycle; occasionally it would get through 2 rounds, but the bolt would rarely pick up the next round and it would barely eject the spent case. A typical under-gassed issue, so I initially thought…

The typical causes of an under-gassed AR are:

  • Gas Port / Gas Block Alignment
  • Loose / Damaged Carrier Key
  • Damaged / Missing Bolt Gas Rings
  • Dirty or Over Lubricated Operating System
  • Bad or Low Powered Ammunition

So first things first, we checked out the bolt carrier, and made sure the carrier key was installed correctly and the screws were tight and staked correctly. Then we checked out the bolt assembly and made sure it was nice and clean and the rings were not damaged. Then we tried firing the rifle again, and got the same results. So then we removed the rail assembly, and the gas block. The gas block was partially covering the gas port on the barrel, it was not completely off, but it definitely wasn’t installed perfectly. After correcting that, we went and tried shooting the rifle again… we had the same results. So we got some samples of ammunition; Winchester, some “hot” reloads, and any other rounds we could find and still, they all exhibited the same issues.

Well what do you check next? Well, everything! We took the gun apart, completely, checking to make sure everything, even unrelated parts were correct, clean and in 100% working order.

After getting the rifle torn down, we noticed the rifle had a rifle length stock, buffer and a carbine length spring (but it was on the long end). So, the next step was to get a new spring, the correct rifle length spring.

If you don’t know, there are rifle length springs and buffers and carbine length springs and buffers. The springs are similar in length, but the rifle length springs should be about 1.5-2″ longer. It’s not a lot, but it makes all the difference in the world.

Once we got a new rifle spring, everything started running like a Swiss watch, nice and smooth! The issue, I think, was that with the lighter spring the bolt carrier was able to slide back too easily, causing the system to off-gas too quickly and causing short-stroking and feeling like an under-gassed rifle.

So my gunsmithing checklist for an under gassed (or seemingly so) rifle, now includes verifying the buffer and buffer spring are correct (something that is generally a good idea with any malfunctioning AR rifle).

My (more) complete list of things to check for a short-stroking and/or under-gassed AR:

  • Correct Buffer / Buffer Spring (carbine or rifle)
  • Gas Port / Gas Block Alignment
  • Loose / Damaged Carrier Key
  • Damaged / Missing Bolt Gas Rings
  • Dirty or Over Lubricated Operating System
  • Bad or Low Powered Ammunition